What do you get
Immediately warn you that for a really good master class I do not have pictures. Missing tried to draw. I hope it will more or less clear.
Let's begin.
1) You will need 4 rings, 3 for most boxes, and 1 for the cover. (Rings, in principle, can be made from wire, but would be willing to ponadezhnee). I have a diameter of about 7 cm
2) All rings are square-braided wiring. It is important to make sure that the harnesses were in exactly the same, or did not really happen. Well. Differences except in the colors. Here is how to make a harness specifically for this case (by myself I know that not everyone knows what a square tow):
2.1) first to make the belt in three rows, a bit shorter than you need to grasp the ring
2.2) close to the tow ring
2.3) and then doplesti missing patch to completely cover the ring, the result is a
2.4) so all the braided ring. Once again, note that it is important that harnesses were exactly the same.
3) Now we need to bridge the ring.
3.1) The figures shown as a bridge the two rings.
And so on around the ring with a gap of three crosses
3.2) formed in the gaps need to attach the beads (I have a cat's eye)
3.3) Now for the construction of two vibrations must priplesti third ring in the same manner.
4) Now you have to make the bottom and the Cabinet. There used quadrupeds on the site diagram of twists, but I had a few extend this scheme (the original scheme lacked a bit)
4.1) obtained from a snowflake to sew to the bottom of the ring box and lid. Tried to depict how to do it.
5) to the ring floor boxes must also attach a small stalk (at least I have them, but their presence is not so much). They weave as well as bridges between the rings is just the height of a "cross"
6) And last, to finish the cover.
6.1), first dopletaem a number of square bundle (only slightly modified) to the ring cover. When viewed from above, the additional number of wiring will look like. (Green is the additional tow)
6.2) now dopletaem another row to the cover to be "dressed" in a box (here the number should be flat, but not burn). The diagram is drawn, what happens if we look at the cover side: (light blue - this additional number, green - what is already there)
Immediately warn you that for a really good master class I do not have pictures. Missing tried to draw. I hope it will more or less clear.
Let's begin.
1) You will need 4 rings, 3 for most boxes, and 1 for the cover. (Rings, in principle, can be made from wire, but would be willing to ponadezhnee). I have a diameter of about 7 cm
2) All rings are square-braided wiring. It is important to make sure that the harnesses were in exactly the same, or did not really happen. Well. Differences except in the colors. Here is how to make a harness specifically for this case (by myself I know that not everyone knows what a square tow):
2.1) first to make the belt in three rows, a bit shorter than you need to grasp the ring
2.2) close to the tow ring
2.3) and then doplesti missing patch to completely cover the ring, the result is a
2.4) so all the braided ring. Once again, note that it is important that harnesses were exactly the same.
3) Now we need to bridge the ring.
3.1) The figures shown as a bridge the two rings.
And so on around the ring with a gap of three crosses
3.2) formed in the gaps need to attach the beads (I have a cat's eye)
3.3) Now for the construction of two vibrations must priplesti third ring in the same manner.
4) Now you have to make the bottom and the Cabinet. There used quadrupeds on the site diagram of twists, but I had a few extend this scheme (the original scheme lacked a bit)
4.1) obtained from a snowflake to sew to the bottom of the ring box and lid. Tried to depict how to do it.
5) to the ring floor boxes must also attach a small stalk (at least I have them, but their presence is not so much). They weave as well as bridges between the rings is just the height of a "cross"
6) And last, to finish the cover.
6.1), first dopletaem a number of square bundle (only slightly modified) to the ring cover. When viewed from above, the additional number of wiring will look like. (Green is the additional tow)
6.2) now dopletaem another row to the cover to be "dressed" in a box (here the number should be flat, but not burn). The diagram is drawn, what happens if we look at the cover side: (light blue - this additional number, green - what is already there)
Không có nhận xét nào:
Đăng nhận xét